technosat 5500 all cam
 

سوفتوير تكنوسات 5500 اول كام

مشكور

رد
 

بس اين اللودر الخاص به

السلام عليكم ورحمة الله وبركاته
ارجو من الأخوةالمشرفين تحديد قسم لبرامج التكنوسات, :)

التكنوسات 5500
 

السلام عليكم ورحمة الله وبركاته
كل عام وانت بخير
هل يوجد سوفت وير للتكنوسات 5500يفتح بدون كامه اوكارت
وشكرا

ماهو البرنامج المستخدم لعملية الترقية الرجاء ارفاقة

Re: التكنوسات 5500
 

نعم يااخى يوجد له ياتش ليعمل بدون كام اوكارد

البرنامج الوسيط هو الهايبرتيرمنال وهو احد تطبيقات الويندوز وموجود بكل كومبيوتر واليك هو جاهز

وهاهى طريقة التعامل مع البرنامج الهايبر
 

Before starting, please make sure the connection with your PC and receiver.

First of all, your Hyper Terminal has to be set as followed.
HyperTerminal Setting

Bit per Sec. : 57600
Databit : 8
Parity : None
Stop bit : 1
flow control : None

First of all, please download "boot_*.bin" file first. This file make the receiver working with copy to copy function. (This file is only for IRCI model!!!)

1. When you turn on the Power button (Not stand-by button), you will see the following massage on the Hyper Terminal. (If your receiver don't have Power button on the rear panel, please pull out the power cord from the socket and push it again) (If the "Caps Lock key" is selected on the computer keyboard, download process is not working. Please check this.)

Z-Modem To upgrade SW, Press 'z' key within 1 sec

2. You have to press "Z" key on the keyboard within 1 second as above message. (Very quickly!). You will see the following massage.

SW Upgrading...

Select one....
1. S/W Upgrade.
2. Boot Upgrade.
3. Quit.

3. Please select "2".

4. You will see "Enter Password" massage on the Hyper Terminal.

5. Password is "1234". Please press it.

Now the receiver will be automatically setting itself. After finishing the process, please download "r*.*" file.

1. When you turn on the Power button (Not stand-by button), you will see the following massage on the Hyper Terminal. (If your receiver don't have Power button on the rear panel, please pull out the power cord from the socket and push it again) (If the "Caps Lock key" is selected on the computer keyboard, download process is not working. Please check this.)

Z-Modem To upgrade SW, Press 'z' key within 1 sec

2. You have to press "Z" key on the keyboard within 1 second as above message. (Very quickly!). You will see the following message.

SW Upgrading...

Select one....
1. S/W Upgrade.
2. Boot Upgrade.
3. quit.

3. Please select "1" and you will see the following message.

:
Ok! Now, send the file...

4. After above massage, please select the file and send it. After the file sending, you will see "good" on the front panel. DON'T TURN OFF THE RECEIVER. The receiver will be reset automatically.

5. You will see the following message on the Hyper Terminal.

Now, flash erasing. Wait a minute.
************
And then this message will be changed as following.

Write

oooooooooooooooooooooooooooooooooooooooooooooooooo ooooooooooooooooooo

Finally you will see the following message.

END

Now you can turn off the receiver.


************************************************** *******************

مشكور ابوخالد ولكن اين اللودر والباتش

الله يعطيكم العافيه
 

الله يقويكم ويعطيكم الف عافيه
عندي رجاء اخوي اريد باتج التكنو 1100 الجديد
مع الف شكرا

انة يفتح الملتي فيجن فقط لا غير اما الايبي سات لابد من وضع كرت